This can allow for merging of lines, or connecting smaller lines to the main line. These large stations can allow multiple trains drop off, or pass through the station. May take up a large space if merging/splitting linesĪ Drive-thru station with trains going in both directions.May be complex to manage if merging lines, and then splitting them after.May cause big accidents and revenue loss if an accident occurs, due to blockage if there is only one line being split up like shown.Versatile with all kinds of lines and different uses.Can load/unload a lot of more trains than previous.You'll notice these are actually 2 simple stations put together. With this type, you can handle lines going in different directions, but not on the same platforms (turns into a two way line). This kind of Ro-Ro station can handle more trains, and can work in incorporating different lines together, even ones going in the opposite way! Just make sure you don't actually follow the set up in the picture if you're going to do that, or you'll have collisions. This can probably handle more trains, like 5-6 or so. Unintentional blockage from block signals ahead of the station are a sure way to mess up the flow of the stationĪ concept for a complex Ro-Ro station.Can handle more trains than Terminus stations, but may cause congestion with multiple trains waiting.Can cause nasty accidents without proper signal usage, especially from the waiting line.One way allows for smoother entries and exits.Simple Ro-Ro stations allow for a few trains to be near the station. Unlike the terminus station, you can only have one way trains unless you want to have a collision or a stuck train. They allow for a queue line behind the station. Ro-ro stations (also called Roll in, Roll out or Roll on, Roll off) are usually in the middle of train lines, especially passenger lines. Ro-Ro station with a wait line due to conveniently placed signals. Note the stopped train outside the lower section. Can't handle long trains if built like in imageĪ simple Ro-Ro station with trains.Can be a disaster if signals are placed incorrectly, or if there are too many trains in the station.transporting goods from the same platform that is used to deliver raw materials or many trains on the line) Can cause gridlocks if overwhelmed (e.g.Trains don't have to go into the same side in the station if it's taken.If you zoom in on the gif, you may see the one way path signal on the right, which is used to prevent collisions and blockage. Due to the fact that this is a two way station, accidents and gridlocks can happen if there are too many trains. This allows trains to cross to the other side if the spot is taken. Note the crossover just outside the station. The Terminus station is a two way station that can be used at end of lines. Signals are what keep the trains from running into each other. Typically, they can't hold a large number of trains, but they are easy to construct.Ī terminus station in action. These stations are recommended for beginners, and are very useful on secondary lines or smaller main lines. 1.5 Combined Terminus and Ro-Ro Station.In this video, I also show the rest of the track layout, a quick ride on a train, and placing orders on new trains. When placing signals near the Station, you might have issues placing this signal, you need to move your mouse to the bottom end of the tile, there are only a few pixels of space where it registers the signal on the proper side.Īnd here's a video of the Station in action.The rest is identical to the Simple RoRo station described above, add signals at the connection to the main line.ĭue to long rails before and after the station, there is one extra step - place signals at the Station entrances and exits:.Then reach out with the main line, you want at least 6 tiles long, not including the tunnel connection.On the entrance side, reach your platform lines out to the level of your tunnel:.Build the tunnels, then you can complete your Station.Now create the holes for your tunnel, you need at least 2 tiles of free space between the tunnel and the Station.However the tunnel too long, and having multiple trains pass through can cause waiting times. Due to the graphical glitches with the Stations above, we can use this build to simulate the free tracks in the middle.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |